Skip to content

Light-gap planning

How far should blackout curtains overlap the window?

Compare curtain pole extension, projected fabric coverage and wall returns with clear diagrams, then plan side, top, centre and lower overlap.

Full-length dark curtains drawn across a bedroom window with generous wall coverage

Extend hardware beyond the opening where the wall and fixings permit.

Leave enough panel width to keep folds and make a centre join.

A wall return controls side light that flat width alone may not hide.

Side overlap starts with the pole or track

There is no single overlap number that makes every bedroom dark. A narrow window in a shallow wall, a bay with angled sides and a broad glazed door produce different views of the edge. The practical question is whether the closed curtain hides the full opening from the place where darkness matters. Stand at the bed or seat and look towards each outer edge; a straight-on view alone can miss a bright sliver.

John Lewis's curtain buying guide uses roughly 15–20 cm of pole extension beyond each side as a common starting point. Mark that on the wall, then check whether there is room for brackets, an open stack and any nearby furniture. For blackout use, a deeper reveal or side-on view may require more. Measure the usable hanging span after choosing the extension, then calculate panel fullness from that span—not from the glass.

An opaque curtain that stops exactly at the frame can still allow light to travel around the outer edge. Increasing pole length helps only if the panels are wide enough to reach the ends and close at the centre. Our curtain-measuring guide separates these dimensions.

Separate pole extension, fabric overlap and returns

A longer pole creates room for fabric and an open stack. It does not establish where the closed curtain edge finishes. A return uses fabric along a different path, towards the wall. Plan all three before treating a pole measurement as a coverage measurement.

Front view: hardware is not fabric coverage

Curtain pole extension compared with projected fabric coverageAn illustrative 1,500 mm opening has a 1,900 mm front pole span, extending 200 mm each side. The closed fabric covers a projected 1,700 mm, overlapping the opening by only 100 mm each side. Decorative finials are not included in the pole span.Usable front pole span: 1,900 mmProjected closed fabric: 1,700 mmOpening: 1,500 mm
Illustrative widths, not recommended allowances: the pole extends 200 mm each side, while the cloth in this sketch covers only 100 mm each side. The centre band marks a join. Projected closed coverage is not the pair’s flat fabric width.

Plan view: why a wall return is different

Curtain end without a return and with fabric returning to the wallTwo schematic plan views compare a curtain ending in front of the wall with one turning back towards it. The return occupies part of the wall-to-curtain distance and can intercept an oblique route around the outer end; it is not extra front-span overlap.No returnFabric returns to wallAn oblique route around the endReturn uses a separate fabric pathSchematic plan views — not a light-performance model
The dashed lines illustrate an edge route, not a ray-traced or measured result. Return geometry depends on the pole/track, end fixing, heading and available fabric. It does not close the gap above the curtain or guarantee a sealed centre.

For the width calculation, the pair-width calculator records returns separately from the front span. If your supplier has already included the return in its usable track measurement, do not add it again. Keep the exact heading and drop reference on the curtain measuring worksheet.

Top and bottom are separate measurements

Mounting a pole higher than the opening lets the heading cover the top of the frame. John Lewis suggests around 10–15 cm above many windows as a planning figure, but ceiling height, eyelet position, brackets and coving may change the right location. A low pole can expose a bright strip above the cloth, even when the side overlap is generous. A ceiling track or pelmet may address the same route differently. See reducing light above curtains.

At the bottom, choose whether the panels finish below the sill or near the floor. A floor-length pair often conceals an awkward sill gap but can interfere with a radiator or collect damp where condensation is persistent. A short panel should at least cover the exposed glazing. Use the selected heading's drop diagram: an eyelet's nominal length does not start at the same point as a pencil-pleat hook. Avoid a long puddle where people may step on the fabric.

Centre overlap and wall returns

The two leading edges must meet when the pair is closed. If they only touch under tension, a vertical gap may reappear after the fabric settles. A track with a designed overlap arm can place one panel ahead of the other; not every track includes one. With an ordinary pole, a fuller pair and sensible ring or eyelet placement may give a better centre join. Do not force clips or magnets onto a fragile lining without considering care and daily movement.

At the outer edges, a return brings the final part of the curtain towards the wall. Some poles curve back; some tracks bend or include a return component. This can reduce the oblique path between wall and fabric. French-return pole guidance illustrates the geometry, but compatibility with your heading and wall matters more than the name. A wraparound pole does not create enough fabric width by itself.

The selected curtain is an eyelet style; check pole diameter, panel width and bracket support before combining it with a return-style pole. If the wall cannot take a wide pole, a close-fitting blind behind the curtain may give staggered edge coverage.

Test the planned coverage in daylight

Use removable tape to mark the intended pole ends and top position. Hold a large sheet or the existing curtain where the new fabric would fall. Move to the pillow or desk and look for top, side and centre gaps. Repeat when the sun is on that window; a night-time test is not revealing. Photograph the problem rather than assuming all light comes through the material.

After fitting, open and close the pair several times. Check that brackets stay firm, the centre still meets and the fabric does not snag on a handle. A stronger rod or middle bracket may be needed for a long heavy span. For children, any separate blind layer must keep cords and chains inaccessible, following UK safety guidance. If side glow remains, use our side-gap troubleshooting guide to decide between extension, returns or a second layer.

Products for this job

Hardware and curtain examples

A return-style pole and an eyelet pair illustrate two different parts of an overlap plan; check their exact sizes independently.

Wall-return pole

Umbra Twilight wraparound curtain pole, black, 30–84 in

Best for: Bringing eyelet curtain ends closer to the wall

A curved-end steel curtain pole that lets a compatible curtain return towards the wall instead of ending in front of the window edge. It addresses side spill, not the gap above the heading.

What stands out

  • Curved ends bring fabric back towards the wall
  • Adjusts across the listed span
  • Supplied hardware includes a centre support

Keep in mind

  • The curtain still needs enough width to form the return
  • A centre support and sound wall fixings are essential
  • Does not close a bright gap above the pole
  • 30–84 in adjustable span
  • Black steel
  • Single wraparound pole
  • Centre support required
Flexible size range

Deconovo blackout eyelet curtains, black, 46 × 54 in, pair

Best for: An affordable ready-made eyelet pair

A widely sized pair of soft eyelet curtains made for a standard pole. The dark colour is useful where room darkening matters more than a pale decorative finish.

What stands out

  • Many size and colour variants are grouped under the listing
  • Pair format suits conventional bedroom windows
  • Simple eyelet heading is quick to hang on a compatible pole

Keep in mind

  • Darkening depends on pole position, width and centre overlap
  • Eyelets can leave a bright band above a low-mounted pole
  • The listing's thermal wording is not a measured room-saving guarantee
  • 46 × 54 in
  • Pair
  • Eyelet heading
  • Polyester

Clear answers

Frequently asked questions

Short answers to the fitting, use and care questions that most often change the result.

Is 20 cm of overlap enough on each side?

It is a useful planning starting point for many windows, not a guarantee. Deep reveals, oblique views and curtain folds may call for more, while limited wall space may allow less.

Do I need overlap above the frame?

Yes if the existing top gap is bright. Position the hardware and heading so the curtain masks the top of the opening, while leaving room for brackets and movement.

Should the two curtains overlap in the centre?

A modest overlap can reduce a vertical line of light. Some tracks offer an overlap carrier, but ordinary poles and headings need enough panel width to meet without tension.

Does a wraparound pole eliminate side gaps?

It can bring fabric towards the wall, but the result depends on the curtain heading, end-ring position, bracket depth and available panel width.

Can a short curtain still block light at the bottom?

It may if the sill or other treatment closes the gap, but a hem ending high above an exposed opening usually leaves a bright band. Check the finish in daylight.